Dial, Digimatic, Firm Joint, Jenny, Slide, Spring Joint and Vernier Calipers.
total: 18 items
Adjustable, depth gauge, external and internal micrometers and micrometer setting gauges.
total: 10 items
A simple tool which enables you to rapidly and accurately locate the centre of a round metal bar or turned wooden section. The tool has a 90 degree notch cut in one side and a blade which bisects the notch with its straight edge.
total: 2 items
Can be used as a square, height gauge, depth gauge, level, marking gauge, scriber, centre gauge, bevel protractor. Supplied with steel rule 12in (300mm)
total: 11 items
Reference charts and tables for the drawing office, toolroom or workshop. Containing data on standard drill sizes and decimal equivalents tapping drills and clearances for metric and imperial threads. Also long tables for sine, cosine, tangent and cotangent.
total: 1 items
High speed tapered steel cutters with 1/4in hexagon shanks for quick change in 3 jaw chucks or hexagon adaptors.
Dial Indicators
total: 3 items
Designed with a knurled spigot to facilitate the scribing of circles. Adjustment made by means of a knurled nut on a threaded rod. Dividers normally have two identical legs with hardened points.
These levels have precision ground bases with a full V groove for suction on a cylindrical workpiece.
Bearing, Flat, Half Round and Three Square Scrapers are designed for removing high spots on machine surfaces and to give a smoother surface on slideways, bearings and cast iron surface plates. Hardened with a light temper so able to maintain a keen edge for longer periods.
total: 9 items
Grade A, B and Graduated Squares. All metal try squares in various length. A notch is cut in the stock in line with the inside of the blade for accurate measurement, even when there is a burr on the edge of the neck. Available in workshop grade B or inspection grade A.
Manufactured from quality hardened steel, Available with either square or one bevelled edge. Finished ground on all edges. Grade B suitable for general workshop use. Grade A precision, inspection and workshop use.
Gauges - Depth
Gauges - Feeler
total: 6 items
Radius Gauges
Screw Pitch Gauges
total: 5 items
Surface Gauges
Telescopic Gauges
Gauges - Wire
Magnets and magnetic tools.
total: 36 items
The Pin Chuck designed for holding drills to small to be held by standard capacity drill chucks. Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are of tubular design and Knurled for easier grip.
Automatic Marking, Belt, Centre, Letter, Nail, Number, Parallel Pin, Sheet metal and Wad Punches.
total: 37 items
These punches automatically strike a blow when downward pressure is applied, no hammer is required.
Used for cutting holes in soft material such as leather, manufactured with ground polished taper section and a milled clearway for removal of waste materials.
Used for the accurate marking of centres prior to drilling.
These punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or postcodes on tools, cycles etc..
Used when lining up existing holes in two or more pieces of metal prior to Bolting or Riveting, also used for driving out and removing pins.
Used for removing pins in parallel holes, the pins should be started with a hand or taper punch to avoid damage to the end of the parallel punch.
A quick and easy way to cut clean holes in sheet metal up to 16 gauge. With even load cutting producing a burr free hole that needs no extra finishing. Individually boxed without a key which needs to be ordered separately.
One piece forged wad punches, used for cutting holes in soft materials or for producing discs from the cut metal.
Drill, hand and pipe reamers. Hand Reamers have a square on end of shank, this allows placement into a wrench which rotates by hand. Used for opening out and finishing existing holes, to H7 tolerance.
total: 4 items
A rivet set is a combination tool having a deep narrow hole and a shallow depression in the non-striking end. Used in sequence they are used to form a domed rivet.
For extracting broken Screws and Studs. Two types are available, A type is for use with medium tensile strength screws and studs, B type is for use on high tensile material.
Handy lengths for general machining jobs. Top quality British made. Guaranteed fine standard tolerances. The ends are chamfered and deburred for safety. Imperial sizes nominally 13 Inches long. Metric sizes nominally 333 mm long.
Carbon and high speed steel taps and dies and diestock and tap wrenches.
total: 34 items
For repairing stripped or damaged threads, creating new ones or changing from Imperial to Metric (or vice versa). Made from high quality Stainless Steel, wound to a shape of a Spring Thread. The Insert Coil, larger than the tapped hole is compressed during installation then allowed to spring back permanently into place.
total: 17 items
Design for holding work together while Drilling, Tapping and other Machining Operations. They are made from Case Hardened Steel for extra strength. The ends of the jaw are rounded to permit clamping under shoulders or in recesses.
Useful for laying out and scribing circles beyond the capacity of ordinary dividers. This Clamping device firmly holds scribing points that in certain applications can be replaced by a pencil. The heads are designed to accommodate any size beam from 19 - 38 mm (3/4 - 1 1/2 Inches) in width. Beam is not supplied.
Hardened and Ground Steel supplied in matched pairs, each having V-Grooves central and parallel to the sides and base ensuring perfect alignment. Tapped holes permit mounting on face plates. They are designed for general workshop duties and layout work during light-duty drilling and milling tasks.