Pipe Cutters - Single Handed

Pipe Cutters - Automatic

Pipe Cutters - Adjustable

A wide range of pipe cutters suitable for Copper, Brass, Aluminium, Light Gauge Steel, Plastic, Stainless Steel & Cast Iron Pipes.

Pipe Cutters - Spare Wheels

Replacement Wheels & Cutters for Pipe Cutters

Pipe Cutters - Plastic Tube

Plastic pipe cutter with ratchet action, effective on PVC, Polybutlene, MDP, Polyethene, HEP20(P), Plastic overflow pipe, plastic electrical conduit, supertube, mini trunking, rubber hose, Pneumatic pipe and electrical sleeving.

Pipe & Tube Benders

Mini Pipe Benders are designed for Small Diameter Anneald Copper, Stainless Steel, Aluminium tubes. Various size of fixed Formers on various Benders cover from 3 to 10mm OD.

Pipe Benders - Formers & Guides

Pipe Formers are used with a Pipe Bender to support and form the pipe, in various sizes to accommodate various sizes of pipe and material such as Copper Stainless Steel, Conduit and Steel, Steam, Gas and Water pipe

Pipe Benders - Bending Springs

Internal springs are just a spring made from flattened steel with a taper at one end (which is inserted into the pipe) while the other end incorporates an eye. With the spring within the pipe, the wall of the pipe is prevented from collapsing inwards as it is bent. A specific spring is required for each size of pipe being bent. External springs are for smaller diameter copper piping. Again they are made from flattered steel but with a 'funnel' at each end so that the copper pipe can be fed through the centre of the spring. With the spring surrounding the pipe, the spring prevents the wall of the pipe from spreading outwards as it is bent. Each pipe size requires its own specific spring.

Pipe Benders - Spares

Selection of spares & Accessories for Pipe Benders

Air Bags & Gauges

Air bags are used for blocking off pipes for maintenance and repair work. They are constructed of rubber inflatable bladders with a canvas protective case. Various gauges are used for water pressure on drain pipes (Air gauge) and mains water pressure (Test gauge).

Drain Test Equipment

Drain Test Equipment consists of Drain Test Plugs and a Drain Test Kit including a U Gauge/Manometer Pressure Gauge.

Gas Testing Equipment

Gas Test Gauges can be used for checking and setting gas pressures on domestic and commercial appliances and for testing pipe work installations with air for leaks before the introduction of gas.

Pipe Dry Testing Kit

Pipe Vices - Chain

Can be fixed to a Tripod Stand or Bench. Will hold Steel Pipes by the High Tensile Steel Chain looped over the Pipe and locked into a slot and tensioned by Handle and Screw. They are cast from S G Ductile Iron Size from 1/8 Inch to 8 Inch OD is available.

Pipe Vices - Hinged

Can be fixed to a Tripod Stand or fixed to a bench, will hold Steel Pipe from 1/8 Inch to 6 Inch OD according to Vice capacity. Work piece is easily placed on Bottom Jaws and Secured by a Self Locking Frame. The frame is reversible for right or left-hand operation.

Tripod Stands

Tripod Stands come with a Vice or can be supplied as stand only. The stand has a platform, tray and can be folded for storage when not in use.

Pipe Wrenches - Chain

Chain pipe wrenches provides maximum grip on Round or Irregular shapes and are ideal for Steel Pipe work where pipes are close to walls Etc. The chain is of High Tensile Steel with a High Breaking Strain. Various sizes of wrenches are available.

Pipemaster Irons & Heads

The pipemaster is a unique tool designed to replace the naked flame of a blowtorch, when soldering integral solder ring and feed capillary fittings on domestic copper pipes.

Pipe De-Burrers & Cleaning Brushes

Brushes for cleaning the inside - outside of copper pipes prior to fitting and soldering. Also including Pipe De-Burrers for both copper & plastic pipes.

Olive Removing Tools

Olive Removing Tool for removing Olives from 15 to 22mm Copper Pipe without damage to the pipe.

Socket Forming Tools

Socket Forming Tools are used by driving into the end of a Copper Tube to form a Socket to accommodate another length of Copper Tube of the same size diameter. The Capillary Joint formed can then be Soft or Hard soldered.

Swaging Tool

Tank Connecting Tools

Tank Cutters

For cutting Circular Holes in Light Gauge, Sheet Metal, Plastic and Wood. The Blade is adjustable and will cut holes 15/16 Inches to 5 Inches Diameter. Available with Hexagon Shank or Brace Shank.

Compression Fitting Spanner

A Plumbers compression fitting spanner for tightening and loosening most 15 and 22mm compression fitting nuts.

Tap Reseaters

Various types of Tap Reseaters will re-cut a Smooth and Watertight seat on most taps and will save throwing away a Tap or Stopcock which has a worn seat.

Tap Reseaters - Cutters & Spares

Spare or Replacement Cutters for Tap Reseaters are available in various sizes, for Flat and Bevelled Cutters. Also available 18TPI Double Parallel Bush.

Circular Hatch & Lid Cutter

The Circular Hatch & Lid Cutter is a revolutionary tool from Scottool Ltd, which allows you to cut matching rebated holes and lids at the same time.

Plumbers Hole Saws

Plumbing Hole Saws come in a range of sizes and types, i.e. High Speed Steel Bi-Metal. They also come in kits with the most popular sizes and mandrels to fit.

Smoke Testers & Tracing Dyes

Smoke Testers are used for testing Drains, Pipes, Flues and Chimneys for Leaks and Defects. Dyes are used to locate the direction of Waterflow in Pipes and Drains. Available in a variety of colours.

Water Pressure Gauge

Mains Water Pressure Gauge with a 11 bar maximum Pressure Reading Gauge with 3/4 BSP Thread for fitting to taps.

Soldering & Brazing Pads

Soldering & Brazing Pads

Blowlamps & Gas Torch Kits

Gas Burners and Torches are mostly used with a Propane/Butane gas mixture. Various shaped heads are available for Soldering, Flame Spreading and Pin Point Work.

Gas Burners - Gas Cylinders

Gas Cylinders are fitted with threaded self-sealing safety valves ensuring safe removal from the appliance and re-sealing automatically. Types: Propane/Butane mixture or Pure Butane Produced in various sizes.

Gas Burners - Spares & Accessories

Drain Rod Sets

A set of Drain Rods with Lockfast Connectors and various Drain Cleaning/Clearing Tools such as Rubber Plunger, Work Drop Scraper and Clearing Wheel. (Lockfast remain secure when rotated in either direction of rotation)

Universal Drain & Chimney Rods

Universal Drain & Chimney Rods

Lockfast Drain & Chimney Rods

Lockfast

Drain & Sink Augers

Drain Cleaners are normally Rods screwed together with a selection of heads to remove or dislodge blockage to the drain.

Plungers

Sink Plunger for clearing Sinks, Wash Basins, Showers and Baths, by creating a build up of air pressure by using a Force Cup.

Chase Wedges & Turnpins

Chase Wedges for chasing roofing materials manufactured from Hardwood and fitted with Ferrules top to allow striking with a Mallet.

Dressing Sticks

Dressing Sticks include in the Range, Bossing Sticks, Bending Sticks and Setting Sticks for forming and laying lead and other ductile sheet materials in the roofing and tanking trade. Made from selected Beech Wood.

Lead Ladles - Lead Knives

Lead Ladies are used for pouring Molten Metals and Compounds. Lead Knives are for cutting Sheet Lead, ideal when Lead Flashing Etc Hooked 6 Inch Long Blade

Plumbing Pliers

A range of Plumbing Pliers for use on Plastic Pipes, Copper Pipes, Removing Olives and Soft Touch Pliers with Special Saws, for removing and fitting Cold Plated Taps Etc.

Basin Tap Wrenches

Basin wrenches are designed for use on Compression Fittings, Copper or Polythene on basins and baths. Available in double ended fixed sizes of 15 mm and 22 mm where space is restricted or adjustable type where the head is adjustable to fit different size nuts.

Boiler Pump Multitool

To facilitate the removal and replacement of boiler pump head retaining bolts and bleed screw cover plates.

Immersion Heater Spanners

Immersion Heater Spanners are used fir fitting or removing Immersion Heaters from Tanks. There are 3 types, Box, Flat and Cranked. These are all made from Steel.

Manhole Keys

Manhole keys for lifting Manholes and are available in various lengths. Handle types are T or Triangle Normally in pairs.

Radiator Keys

Radiator Keys for bleeding (or releasing air) from radiators.

Stopcock Keys

Stopcock Keys come either with a standard Crutch Head or a Square Head. Square Keys are 1/2 Inch 5/8 Inch or 3/4 Inch Square Head. Both types are available in various lengths to cope with depth of Stopcock Inspection Chamber.

Taptool Wrenches

The Taptool Wrench is a very versatile tool which can handle most plumbing jobs around the home, including: Backnuts, Spindles, Taps, Valves and Stopcocks.

Waste Pipe Installer

For the difficult task of holding a pop up waste in position when installing into sinks, baths, basins or bidets.